Dash Z Racing Blog
DashZRacing Phone Number 8776414829

Archive for the ‘*Installation Help*’ Category

Installation Instruction for Dashzracing LED Tailgate Bar

Posted by dashzracing On June - 28 - 2010Comments Off on Installation Instruction for Dashzracing LED Tailgate Bar

LED Tailgate bar is the most popular item for lighting parts, the LED Tailgate bar has 49″ and 60″ available at Dashzracing storefront.  The LED Tailgate bar also come with reverse lights function which can let the vehicles behind you more clearly know that when you brake and reverse.  They are the must-have part for your truck.  Get them now at Dashzracing storefront and give your vehicle a brand new look.  If you want to know more information about Dashzracing’s LED Tailgate... more

Installation Guide For 05-09 Dodge Charger Projector Headlights

Posted by Ingar Charlie Bordi On June - 27 - 2010Comments Off on Installation Guide For 05-09 Dodge Charger Projector Headlights

This is an installation guide for 05-09 Dodge Charger Projector Headlights.  We have couple different styles of 05-09 Dodge Charger Projector Headlights in Dash Z Racing, and we also carry different style of 05-09 Dodge Charger corner lights for you to match with your headlights: Regular Halo Projector Headlights for 05-09 Dodge Charger: CCFL Angel Eye Halo Projector Headlights for 05-09 Dodge Charger: Installation Guide: Hardware needed: 1 x Handy Remover 1 x Trim Pad Remover 1 x Flat Tip... more

Installation Guide for 03-06 Infiniti G35 Coupe Sport Grille

Posted by Ingar Charlie Bordi On May - 31 - 20102 COMMENTS

This is an article about how to install the front sport grill for 03-06 Infiniti G35 Coupe.  If you want to see more picture and introduction about these sport grill for G35, please read our previous article: “03-06 Infiniti G35 JDM Skyline Grille“. Installation for 03-06 Infiniti G35 Coupe Sport Grille Step 1: Remove the top 4 pop rivets at the top of the OEM grill (you will need a flathead screwdriver). Be sure to hold onto these pop rivets, they will be needed to secure the Ionic... more

2007-2010 GMC Yukon Denali Junyan LED Projector Headlights This DIY installation guide will help you get a better understanding on how to install the new 2010 Junyan 2007-2010 GMC Yukon Denali led projector headlights. Junyan created a great design for this projector headlight, it’s easy to install, and the best part is it doesn’t have stupid halos to make it look like no damn BMW.   Please remember aftermarket projector headlights should always be resealed before installation. ... more

New 2010 Junyan LED Projector Headlight Installation DIY Guide For 1998-2004 Dodge Intrepid

Posted by Koneko Kumamoto On May - 4 - 2010Comments Off on New 2010 Junyan LED Projector Headlight Installation DIY Guide For 1998-2004 Dodge Intrepid

1998-2004 Dodge Intrepid Halo LED Projector Headlights Low Beam Bulb Size : H7 This DIY installation guide will help you get a better understanding on how to install 1998-2004 Dodge Intrepid led projector headlights made by Junyan.  Junyan made this projector headlight easy to install with interchangeable halo bulbs and led bulbs.  Please remember aftermarket projector headlights should always be resealed before installation.  Check out our guide below before installing your 1998-2004 Dodge... more

Installation for 96-98 Honda Civic EK Fog Lights

Posted by Ingar Charlie Bordi On May - 3 - 2010Comments Off on Installation for 96-98 Honda Civic EK Fog Lights

This installation is for 96-98 Honda Civic Fog Lights from Dash Z Racing.  These 96-98 Honda Civic Fog Lights will fit 1996, 1997, 1998 Honda Civic 2 Door coupe, 3 Door Hatchback and 4 Door Sedan: Tools and supplies Phillips screwdriver Ratchet 10mm socket Extension utility knife Hacksaw blade Dremel/File Step 1: Cutting front bumper There are plastic cutouts on each side of the bumper, but there is a specific way to cut them out. You should have directions that show the right tabs... more

This is a 2010 brand new Junyan projector headlight release for the 1995-1999 Nissan Sentra.  All new completely redesigned projector headlights with halo, led and a straight cut of line feature.   There have been a couple of different headlights released for the 1995-1999 Nissan Sentra in the past but nothing like this new Junyan unit which is a complete 1 piece unit, connecting the projector headlights with corners.  Please remember everyone that the Junyan 1995-1999 Nissan Sentra... more

How To Smoke Car Tail Lights And Motorcycle Tail Lights

Posted by Koneko Kumamoto On April - 24 - 20101 COMMENT

Step 1. Remove the tail lights from the vehicle. Step 2. Clean the tail lights.  Make sure to do a good job on cleaning the tail lights so the smoke paint spray can go on the tail lights with a even smooth finish. Step 3. You’re ready to paint.  Make sure you’re not in a small room because there will be heavy fumes.  Also be prepared with at least two bottles of the smoke paint spray just in case you want a darker look on the tail lights.  Paint with very light coats and let it... more

Honda Emblem and installation Guide

Posted by Travis Buckley On April - 21 - 2010Comments Off on Honda Emblem and installation Guide

Looking for Emblems to replace your Honda Hood/Trunk piece? DashZRacing carries 4 different colors for your choice: Front Emblem Installation Guide: Step One: Get  emblems ready Step Two: Pop your hood and find all of these on the top of the front grille area. Removing them is easy. Take your flat head screwdriver and pry UP the middle section. Wiggle the rivet around until it comes loose. Take them all off and put them someplace safe. It will look like this when you’re done. Step Three: Remove... more

C-West Voltage Stabilizer

Posted by Ingar Charlie Bordi On April - 18 - 2010Comments Off on C-West Voltage Stabilizer

Dash Z Racing carries the voltage regulator from C-west in red, blue, silver and gunmetal.  These voltage stabilizers provide a steady amount of electrical current to electronic devices when power fluctuates when your car is running.  Power surges and sudden power drops can cause serious damage to electronic devices in your car, and these voltage stabilizers store power and provide power from its reserve to attached devices, which bypasses power fluctuations. To learn more about the installation... more

Installation for Apexi Pen Style Turbo Timer

Posted by Ingar Charlie Bordi On April - 18 - 2010Comments Off on Installation for Apexi Pen Style Turbo Timer

A turbo timer is a digital device to keep your engine running for a period of time in order to cool down the turbocharger and prevent turbo wear and failure.  It is very important for turbocharged engine to run at idle speed for a period of time and allows teh compressor to coll from lower gas temperature in both the exhaust and intake tracts.  At the same time the lubricating oil from the engine is able to circulate properly so the turbine won’t burn the lubricating oil that would otherwise... more

Led & Halo Projector Headlight Installation DIY Wiring

Posted by Koneko Kumamoto On April - 3 - 201010 COMMENTS

Projector headlights are very popular in the auto industry.  The troublesome part about them as been installation.  With the trends constantly charging with halos, ccfl halos, and leds installation has always been a B@tch!  I wish manufacturers from over seas would just simply put the loose halos wires and led wires into the main plug and them these different types of projector headlights on the market can finally become “plug and play” (a term misused by every projector headlight... more

Continued on the previous post about 99-00 Honda Civic Fog lights installation, now we are about to start on wiring the fog lights and placing the harness to the interior.  As a reminder, Dash Z Racing carries these 99-00 Honda Civic Fog Lights in clear lens, JDM yellow lens and smoke lens: Wiring the Fog Lights Pictured on the top is the passenger-side where I routed the wiring harness under the airbox and attached the relay to the back of the airbox.  I bundled the cabling, leaving the... more

Has This Ever Happened To Your Headlights? Moisture being trapped inside of projector headlights or OEM headlights has always been a common problem.  In order to seek the proper answer to this issue we first need to understand the problem at hand.  First, moisture inside of your projector headlights or stock headlights does not mean there is water leaking from them.  There are a couple of reasons why moisture may start to form inside your headlights.  This occurs when cold weather or other reasons... more

Power Antenna Installation Guide

Posted by Ingar Charlie Bordi On March - 23 - 2010Comments Off on Power Antenna Installation Guide

Removing Original Antenna Step 1 Activate the antenna switch to the up position. Step 2 Using the wrench or needle-nose pliers, loosen and remove the original retaining nut on the base of the antenna mast. Step 3 Gain access to the underside of the area where the antenna is located. Step 4 Remove the bracket or brace that is below the hole and holding the antenna in place. Step 5 Remove the mast. Step 6 Find the motor that controls the antenna mast. Generally, power antennas will have a constant... more